# Carbonite Black Tallies to Ultrix

**URL:** <https://rossvideo.community/t/carbonite-black-tallies-to-ultrix/10903>\
**Category:** Production Switchers\
**Created:** [August 30, 2023, 1:13pm UTC](https://rossvideo.community/t/carbonite-black-tallies-to-ultrix/10903 "2023-08-30T13:13:00Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![sylvainlevacher](https://rossvideo.community/letter_avatar_proxy/v4/letter/s/b2d939/32.png) [@sylvainlevacher](https://rossvideo.community/u/sylvainlevacher)\
**Post date:** [August 30, 2023, 1:13pm UTC](https://rossvideo.community/t/carbonite-black-tallies-to-ultrix/10903/1 "2023-08-30T13:13:00Z")

</div>

Hello,

After a reset, my Carbonite black switcher lost the configuration used to communicate the TALLYs with the Ultrix.

This switcher has been upgraded to version 15.6.1.19113. I can no longer find the menus used to configure the TSL\_UMD protocol, which is used to communicate tally status to the image mosaic managed by the Ultrix.

What I do to configure

System —\>Device Config —\> Add new —\>Serial tally —\>Add 0-TSLumd\_1.0 —\>confirm

In my memory, on version 12 of the switcher, you could set the communication port used. I can’t find this part of the menu.

Can you tell me what settings I need to make to configure this gateway with the ultrix?

Thank’s

Sylvain

---

<div class="post-metadata">

**Author:** ![leso\_reilly](https://rossvideo.community/user_avatar/rossvideo.community/leso_reilly/32/159_2.png) [@leso\_reilly](https://rossvideo.community/u/leso_reilly)\
**Post date:** [August 30, 2023, 7:26pm UTC](https://rossvideo.community/t/carbonite-black-tallies-to-ultrix/10903/2 "2023-08-30T19:26:00Z")

</div>

The Manual is available directly on the website in searchable HTML form:

[https://help.rossvideo.com/carbonite-02/?\_gl=1\*vrbsmh\*\_ga\*NTUyMTAxNDIzLjE2Nzk1NzcxMjU.\*\_ga\_H7SG1QNZ8K\*MTY5MzQyMzQ1My41My4xLjE2OTM0MjM0NjAuNTMuMC4w](https://help.rossvideo.com/carbonite-02/?_gl=1*vrbsmh*_ga*NTUyMTAxNDIzLjE2Nzk1NzcxMjU.*_ga_H7SG1QNZ8K*MTY5MzQyMzQ1My41My4xLjE2OTM0MjM0NjAuNTMuMC4w)

The link to the TSL Device configuration can be found here:

[https://help.rossvideo.com/carbonite-device/Topics/Devices/UMD/TSL.html#topic.tsl](https://help.rossvideo.com/carbonite-device/Topics/Devices/UMD/TSL.html#topic.tsl)

I am guessing you are adding to the Serial Port not adding a new device and selecting a IP “SLOT” for the device.

---

<div class="post-metadata">

**Author:** ![sylvainlevacher](https://rossvideo.community/letter_avatar_proxy/v4/letter/s/b2d939/32.png) [@sylvainlevacher](https://rossvideo.community/u/sylvainlevacher)\
**Post date:** [August 31, 2023, 9:36am UTC](https://rossvideo.community/t/carbonite-black-tallies-to-ultrix/10903/3 "2023-08-31T09:36:00Z")

</div>

Thank you less for your reply,  
it’s the Next button that was missing in my setup procedure. I was able to set the IP address and port value.  
Everything is working properly now.

Sylvain

---

<div class="post-metadata">

**Author:** ![leso\_reilly](https://rossvideo.community/user_avatar/rossvideo.community/leso_reilly/32/159_2.png) [@leso\_reilly](https://rossvideo.community/u/leso_reilly)\
**Post date:** [August 31, 2023, 1:36pm UTC](https://rossvideo.community/t/carbonite-black-tallies-to-ultrix/10903/4 "2023-08-31T13:36:00Z")

</div>

Thanks for following up!