Profile

Brett Blank

Contact Details

My Content

1 to 20 of 35 total

Save failed

Posted By Brett Blank 01-28-2018 21:55
Found In Egroup: Production Switchers \ view thread
Tried to save a set but display said failed. I was able to load all of the sets I have saved but couldn't save to any of them. I changed the date/time through the config button. After I did this is when I got save failed message. I am running the latest version of the carbonite softwar ...

RE: Keys and Keying

Posted By Brett Blank 11-10-2016 20:38
Found In Egroup: Production Switchers \ view thread
Just emailed you #Carbonite

RE: Keys and Keying

Posted By Brett Blank 11-10-2016 16:21
Found In Egroup: Production Switchers \ view thread
Now I see what you are talking about. On the configuration menu, ME 1 Clean Feed has the Key 4 button highlighted. How would I un-highlight that or can I? How can I get Key 4 to work? #Carbonite

RE: Keys and Keying

Posted By Brett Blank 11-10-2016 15:34
Found In Egroup: Production Switchers \ view thread
I'm in live assist, looking at the buses. key 4 is set to the physical button I want it set to (like the other three keys which work) but key four still doesn't work #Carbonite

Keys and Keying

Posted By Brett Blank 11-09-2016 20:18
Found In Egroup: Production Switchers \ view thread
I moved something onto Key 4 today and couldn't get it to work. As a test, I switched what was in Key 1 to Key 4, and it didn't work but what was in Key 4 worked in Key 1. I even swapped out the custom control from Key 3 to Key 4. Everything worked, made the cuts, turned on/off keys, rolled the ...

Dashboard v8 user manual

Posted By Brett Blank 11-08-2016 17:24
Found In Egroup: Facility Control \ view thread
The Dashboard section on the website still has the v7 user manual. Where can I find the v8 user manual?

RE: Designer question

Posted By Brett Blank 11-08-2016 16:31
Found In Egroup: Graphics \ view thread
Thanks! #XPression

RE: Designer question

Posted By Brett Blank 11-08-2016 16:00
Found In Egroup: Graphics \ view thread
and a user guide I can print? Cant find one on the computer we are using with designer #XPression

Designer question

Posted By Brett Blank 11-07-2016 22:33
Found In Egroup: Graphics \ view thread
1. Where can I find a user guide I can print? 2. Since I am using Designer, even though I can make an animation sequence, I can't take that animation live correct? (it will look like a still graphics instead of moving)

RE: Xpression linking to OES scoreboard

Posted By Brett Blank 10-31-2016 20:33
Found In Egroup: Graphics \ view thread
Ok, that makes sense. #XPression

RE: Xpression linking to OES scoreboard

Posted By Brett Blank 10-31-2016 20:27
Found In Egroup: Graphics \ view thread
we would use COM1 or COM3 still? #XPression

RE: Xpression linking to OES scoreboard

Posted By Brett Blank 10-31-2016 18:57
Found In Egroup: Graphics \ view thread
We tried several different configurations. 1. RS232 cable from the OES distro box to the Xpression computer using COM 1 and COM3 - no luck 2. RS232 cable from the OES ISC9000 box to the xpression computer using COM 1 and COM3 - no luck 3. We tried a RS232 cable we know works (OES distro box ...

RE: Xpression linking to OES scoreboard

Posted By Brett Blank 10-18-2016 18:14
Found In Egroup: Graphics \ view thread
The documentation for the computer just says serial port #XPression

RE: Xpression linking to OES scoreboard

Posted By Brett Blank 10-18-2016 17:27
Found In Egroup: Graphics \ view thread
Its from the OES distro box which is connected to the OES controller. #XPression

RE: Xpression linking to OES scoreboard

Posted By Brett Blank 10-18-2016 15:42
Found In Egroup: Graphics \ view thread
We are using a PC to run Xpression Designer. I am not seeing the same graphic card (we have a NVIDIA Quadro K600) Under Device Manager>Ports, I have: Communications Port (COM1) and Intel(R) Active Management Technology - SOL (COM3). There is no USB Serial Port (COM3) listed. I changed ...

RE: Xpression linking to OES scoreboard

Posted By Brett Blank 10-13-2016 20:34
Found In Egroup: Graphics \ view thread
Reading the instructions, does it need to be a USB-serial cable? We have a RS232 serial to serial cable. Will that work? We are using Xpression Designer #XPression

Datalinq connecting to Click Effects and MLBAM

Posted By Brett Blank 10-13-2016 15:43
Found In Egroup: Graphics \ view thread
Is there a way to connect datalinq to click effects and the MLBAM plug in? We are using Xpression Designer.

RE: Xpression linking to OES scoreboard

Posted By Brett Blank 10-13-2016 15:17
Found In Egroup: Graphics \ view thread
Garner, Can you please send me that set up guide? bretta@nashvillesounds.com Thanks #XPression

RE: Datalinq question/issue

Posted By Brett Blank 02-23-2016 17:12
Found In Egroup: Graphics \ view thread
Without knowing any details about the datasource (and what's coming from it) it's hard to make a specific suggestion. Assuming your datasource was going to have a data field that had a value of 1 for runner on base and a value of 0 (or anything not 1) for a runner not on base you could put something ...

RE: Datalinq not updating

Posted By Brett Blank 02-11-2016 22:49
Found In Egroup: Graphics \ view thread
Oh I totally missed that from this other post! FYI - XPression Designer and the RossLinq connection to a Carbonite Switcher only allows for still graphics. Upgrading to Prime, BlueBox or Studio with an SDI framebuffer card is required for SDI video (motion graphics). Man, don't know how ...