Profile

Martin Hertzberg

Contact Details

My Content

1 to 12 of 12 total

More info v11

Posted By Martin Hertzberg 10-07-2015 11:46
Found In Egroup: Production Switchers \ view thread
Hi, I see that v11 is available for download - is there any information on what features or similar that might come with an upgrade?

RE: email notification on parameter change

Posted By Martin Hertzberg 12-16-2014 13:37
Found In Egroup: Facility Control \ view thread
Hello James, and once again - thank you for your reply. The panel is aimed to be something of a high-level/lean-backwards monitoring panel for some of our critical TX/Embedd/media transport-equipment, so I have dragged stuff from just about everywhere into it. I will try the context tip you have, ...

RE: email notification on parameter change

Posted By Martin Hertzberg 12-10-2014 23:49
Found In Egroup: Facility Control \ view thread
Thank you James for your reply. However, it seems as if I am stuck way before I get to the emailing part. I have drag'n'drop a parameter text field from a controller into my grid. The text field updates in real-time and in parameter inspector in debugger, I can see that the parameter changes. To me that ...

RE: Carbonite 2ME panel stuck in 'sleep' mode

Posted By Martin Hertzberg 12-09-2014 23:44
Found In Egroup: Production Switchers \ view thread
We've had the same issue. #Carbonite

email notification on parameter change

Posted By Martin Hertzberg 11-20-2014 21:14
Found In Egroup: Facility Control \ view thread
Hello, In short, I wonder if anyone would be able to point me towards a solution for creating a script for email notification on a specific parameters change in Dashboard. For example, we have a couple of SFS-8622-A for our main and backup TX feeds. If the SDI input signal probe parameter would ...

Get out of loop when loop ends

Posted By Martin Hertzberg 01-25-2013 10:44
Found In Egroup: Graphics \ view thread
Hello everyone, We need some input on how to get the xpn to trigger a video the way we want. We are in a looping video segment. When we give a trigger we want the loop to play to end and then start a new video. any suggestions?

Simple control of Animation controller

Posted By Martin Hertzberg 11-07-2012 12:43
Found In Egroup: Graphics \ view thread
I want to be able to control a simple animation controller from a SmartGPI. In the SmartGPI config I set up a script event and tried this script: -- dim fly as xpAnimController dim vsset as xpScene Engine.GetSceneByName("Scene6", vsset) vsset.GetAnimControllerByName("MonitorUpp", ...

RE: RossTalk

Posted By Martin Hertzberg 07-26-2012 14:30
Found In Egroup: Production Switchers \ view thread
That did the trick! thx :-) #Carbonite

RE: RossTalk

Posted By Martin Hertzberg 07-25-2012 18:49
Found In Egroup: Production Switchers \ view thread
Sorry Les, bad explanation. No the switcher does not take the command/take any crosspoint. We tried a couple of variants, but no response. #Carbonite

RE: RossTalk

Posted By Martin Hertzberg 07-25-2012 18:23
Found In Egroup: Production Switchers \ view thread
Thank you Les, I still have problems with the XPT commands. If I try them the way I interpret the document a cut to source one on Aux 1 would be: XPT IN:1:AUX:1 - this returns nothing from the switcher, can you perhaps give me a hint? #Carbonite

RossTalk

Posted By Martin Hertzberg 07-23-2012 22:49
Found In Egroup: Production Switchers \ view thread
Played around a bit with the RossTalk control of the switcher in v6.2. I telnet to the switcher and it accepts all commands, but the XPT command. Is there a limitation here? I tried for example XPT 1:1 to cut source 1 to aux 1, but no luck. Martin

Manual Blackstorm

Posted By Martin Hertzberg 07-11-2012 22:36
Found In Egroup: Video Servers & Replay Systems​ \ view thread
Hello, on the download section for video servers there seems to only be the SMS manual. Will we see the Blackstorm manual there any time soon? cheers Martin