Profile

João victhor Mariano

Contact Details

My Content

1 to 20 of 50+ total

RE: How to send data to Wideget IP address (14) ?

Posted By João victhor Mariano 04-29-2025 13:14
Found In Egroup: Facility Control \ view thread
Hello, I would like to add one more discovery. I managed to make the above logic work, when I convert the IP to an integer. However, this only worked for class A IPs (up to 127.255.255.255). is that right? Thanks, ------------------------------ João victhor Mariano ---------- ...

How to send data to Wideget IP address (14) ?

Posted By João victhor Mariano 04-28-2025 16:29
Found In Egroup: Facility Control \ view thread
Hello Community, I'm trying to set a custom button in Dashboard to entering with an IP address without need to type it in the field. In nutshell, I'm trying to do this in MC1-UHD-4A card > Remote Control tab > Rosstalk > Network Setup > Remote IP (photo below). I already found this ...

RE: Stream Deck controlling Dashboard Panels

Posted By João victhor Mariano 07-19-2024 13:01
Found In Egroup: Facility Control \ view thread
Hello, Could you help me how to set the Stream Deck to control the soft panels from Ultrix router? ------------------------------ João victhor Mariano ------------------------------

RE: Ultrix crosspoint with frame delay.

Posted By João victhor Mariano 03-26-2024 11:13
Found In Egroup: Facility Control \ view thread
Hello, I'm attaching the panel which I created few days ago. The panel is executing exactly what I need (It Sets the crosspoint SRC:CAM1 - DST:OUT2 and after few miliseconds sets another crosspoint SRC:CAM11 - DST:OUT3). The problem is that,for some reason, the time displayed in ...

RE: Ultrix crosspoint with frame delay.

Posted By João victhor Mariano 03-26-2024 11:12
Found In Library: Facility Control

Ultrix crosspoint with frame delay.

Posted By João victhor Mariano 03-21-2024 10:45
Found In Egroup: Facility Control \ view thread
Hello, I am trying to create a Dashboard panel, so that when closing a crosspoint (SRC1 to OUT2) after 7 frames delay another crosspoint is made (SRC 11 to OUT3). So I created two rows of buttons, with the sources of each output. I created two parameters to associate ...

RE: CustomPanel - Crosspoints with frame delay.

Posted By João victhor Mariano 03-18-2024 16:51
Found In Egroup: Facility Control \ view thread
Hi, Ok,understood. However,regarding the outputs which are not being converted, os it possible to use delay longer than 1 frame? If so, how can I do this? Thanks, ------------------------------ João victhor Mariano ------------------------- ...

CustomPanel - Crosspoints with frame delay.

Posted By João victhor Mariano 03-15-2024 15:24
Found In Egroup: Facility Control \ view thread
Hello, I currently have a Carbonite Ultra switcher running at 4k video mode. I have 3 video sources (CAM1,CAM2,CAM3) that enter the switcher in 1080i format. As the switcher converts them, I'm able to display them in 4K on the Multiviewer. However, a client asked me to create the ...

CustomPanel - Crosspoints with frame delay.

Posted By João victhor Mariano 03-15-2024 15:23
Found In Egroup: Production Switchers \ view thread
Hello, I currently have a Carbonite Ultra switcher running at 4k video mode. I have 3 video sources (CAM1,CAM2,CAM3) that enter the switcher in 1080i format. As the switcher converts them, I'm able to display them in 4K on the Multiviewer. However, a client asked me to create the ...

CustomPanel - Crosspoints with frame delay.

Posted By João victhor Mariano 03-15-2024 15:22
Found In Library: Production Switchers

RE: VDCP custom panel - Dashboard

Posted By João victhor Mariano 11-16-2023 10:59
Found In Egroup: Facility Control \ view thread
Hi, Yes,sure. Thanks. ------------------------------ João victhor Mariano ------------------------------

RE: VDCP custom panel - Dashboard

Posted By João victhor Mariano 11-16-2023 10:58
Found In Library: Facility Control

RE: VDCP custom panel - Dashboard

Posted By João victhor Mariano 11-16-2023 09:22
Found In Egroup: Facility Control \ view thread
Hi Aury, I tested the two panels suggested by Altaz and Jack, but I did not have success on it. In both cases the playlist isnot loaded. Looking at the photos above, Am I doing something wrong ? Thanks, ------------------------------ João victhor Mariano ...

RE: VDCP custom panel - Dashboard

Posted By João victhor Mariano 11-14-2023 16:31
Found In Egroup: Facility Control \ view thread
Hi Altaz, I didn't test the Jack's answers yet, but I'll certainly test you panel too. Regarding this custom panel, Can I assign the server IP address on the "Host field" ? Thanks, ------------------------------ João victhor Mariano ------------------------------

RE: VDCP custom panel - Dashboard

Posted By João victhor Mariano 11-14-2023 07:55
Found In Egroup: Facility Control \ view thread
Hello Jack, First of all, thank you for your attention in this case. Ok,understood. So I'll try the two solutions you sent me and verify which one best suits the customer's operation. Thanks, ------------------------------ João victhor Mariano ------------------- ...

RE: VDCP custom panel - Dashboard

Posted By João victhor Mariano 11-13-2023 17:14
Found In Egroup: Facility Control \ view thread
Hello Altaz, Did you have a chance to check my panel? Unfortunately I have not made any progress in the last few days. Thanks, ------------------------------ João victhor Mariano ------------------------------

RE: VDCP custom panel - Dashboard

Posted By João victhor Mariano 11-09-2023 11:05
Found In Egroup: Facility Control \ view thread
Hi, I'm sorry for that. You'll find the script below. Thank you for your attention. function callbackFunction1(success, cmd, result, exception) ( if (success = 'true') ( ogscript.rename('clipName1',result); //Update Channel 1 Clip Name in playout area params.setValue( ...

VDCP custom panel - Dashboard

Posted By João victhor Mariano 11-09-2023 09:52
Found In Egroup: Facility Control \ view thread
Hello, I need to create a custom panel to control a server through VDCP protocol, however I didn't have success on it so far. The customer has an old Ross server known as "SMS - Softmetal server" which only receives commands from VDCP protocol. It worked fine with his Vision swtcher, but since ...

RE: Stream Deck controlling Dashboard Panels

Posted By João victhor Mariano 11-16-2022 08:57
Found In Egroup: Facility Control \ view thread
Hello Aleksander Stalsberg, First of all, thanks for your tip. Actually, I already installed the Stream Deck app on my PC and I also found the Rosstalk pluggin on it. I´m stuck o how to write the correct command to do my Dashboard panel works as expected. I´m doing a simple test...my Dashboard ...

Stream Deck controlling Dashboard Panels

Posted By João victhor Mariano 11-11-2022 09:06
Found In Egroup: Facility Control \ view thread
Hello, I recently bought a Stream Deck and I´d like to use it to control some buttons in my custom Dashboard panels. I know that it´s possible use Stream Deck to control some functions in Carbonite switcher, Xpression through Rosstalk protocol. However, I´d like to know if is there some commands ...