Profile

Barbara Sharp

Contact Details

My Content

1 to 11 of 11 total

RE: Sending VISCA commands via Dashboard

Posted By Barbara Sharp 01-19-2024 09:14
Found In Egroup: Facility Control \ view thread
Hi Steve, Unfortunately, I don't have an example panel for this, but I can answer your specific questions and provide a few code snippets: You are correct that to control zoom speed, you would use ptzjoystick.vel.zoom In terms of sensitivity, as the Pivot and PTZ-12G are different camera ...

RE: Sending VISCA commands via Dashboard

Posted By Barbara Sharp 01-02-2024 08:47
Found In Egroup: Facility Control \ view thread
Hi Steve, There is an option to vary the pan/tilt speed with the zoom value. It is called Variable Zoom in the DashBoard UI (Config->Camera) and can also be set through the camera web UI. This will reduce the sensitivity of the pan and tilt controls as you zoom in so that you can make finer adjustments. ...

RE: Dashboard Panel - Change to Bank 2

Posted By Barbara Sharp 12-20-2023 09:24
Found In Egroup: Facility Control \ view thread
Hi Steve, Two suggestions for you: 1) Presets are recalled by number. If you have 64 presets in each bank, you would recall the first preset in bank 2 as preset 65 (or 64 if indexed from 0). To do this with a button, you could use it to set the value of a local offset parameter (e.g. set to ...

RE: Dashboard Label for PTZ-12G

Posted By Barbara Sharp 12-07-2022 08:05
Found In Egroup: Facility Control \ view thread
Hi Steve, For that, you need to use the Source tab to look in your code for lines like this - the objectid determines the device that is referred to by any parameters within that element. Slot 1 PTZ-Camera" objecttype="PTZ-Camera" > If you right click on a node in your DashBoard tree, and select ...

RE: Dashboard Label for PTZ-12G

Posted By Barbara Sharp 12-06-2022 09:21
Found In Egroup: Facility Control \ view thread
Hi Steve, For the iris on a PTZ panel, you need paintbox.iris.control. Using the Params -> Label option in the DashBoard toolbox, you can select your target parameter and you should get something like this Barbara ------------------------------ Barbara Sharp Software Developer, Technical ...

RE: Displaying Tally on Dashboard

Posted By Barbara Sharp 06-10-2022 17:10
Found In Egroup: Facility Control \ view thread
I'm happy to hear that it worked for you. Thanks for sharing the screenshot of your panel. Barbara ------------------------------ Barbara Sharp Software Developer, Technical Lead - Robotics Ross Video ------------------------------

RE: Displaying Tally on Dashboard

Posted By Barbara Sharp 06-08-2022 09:19
Found In Egroup: Facility Control \ view thread
Hi Steve, To get access to tally status for the PTZ-12G cameras, you will need a TSL 3.1 tally source. You can then follow the following steps: 1. In your DashBoard tree, find Tally under DashBoard Services to open the DashBoard Tally Service. Select the Configuration page and turn on the listener ...

RE: Can't seem to get Manual Focus to "stick" with PTZ-12 Cameras

Posted By Barbara Sharp 06-08-2022 09:05
Found In Egroup: Camera Motion Systems \ view thread
Hi Steve, Do you have a Carbonite connected to your cameras? This problem typically occurs because the Carbonite will periodically send its desired value for auto focus to the cameras, overriding the value set from other controllers such as DashBoard. Assuming that you have Carbonite connected to ...

RE: Dashboard for Ross PTZ 12-G

Posted By Barbara Sharp 03-17-2022 14:56
Found In Egroup: Facility Control \ view thread
Hi Steve, Transitioning your custom panel to PTZ-12G cameras should be very straightforward. To start with, you will need to add the new cameras to DashBoard and recreate any presets that you need for each one. When you open your custom panel after removing the old Pivot cameras, you will see lots ...

RE: Pivotcam SE not recognized by Touchdrive Linux Dashboard

Posted By Barbara Sharp 06-23-2021 08:57
Found In Egroup: Camera Motion Systems \ view thread
Hi Conrad, Thank you for sharing this information. It looks as though your Pivot camera has only partially been updated to the 2.1a release of the Pivot firmware, so you are running a mix of firmware on the camera which has not been tested together and which is not supported by the DashBoard PTZ Camera ...

RE: PivotCam commands for joystick buttons

Posted By Barbara Sharp 03-10-2021 17:23
Found In Egroup: Facility Control \ view thread
If you look in the User Manual for PTZ Camera Control Plugin (https://documentation.rossvideo.com/files/Manuals/Cameras/PivotCam/User_Manual_for_PTZ_Camera_Control_Plugin_(8351DR-015).pdf) on pages 74 & 75, there is a list of most of the commonly used camera functions that you might want to access from ...